Micron Wings

Motors

Brushed Motors (Rx -> Motor)

Nano Motor 3mm SMD
Diameter: 3.0mm
Length: 10mmmm
Weight: 0.36grams
(more info)

	4mm x 12mm 7 Ohm A 4mm diameter motor with a 0.65mm shaft. weight is 0.71 grams (more info) (NEW Lower Price for multi-pack)
	6mm x 15mm Negative Can Diameter: 6mm Length: 15mm Voltge: 1S (3.7V) Direction: Negative (Anticlockwise) (more info)
	6mm x 15mm Positive Can Diameter: 6mm Length: 15mm Voltge: 1S (3.7V) Direction: Positive (Clockwise) (more info)
	6mm x 14mm 3.6 Ohm A 6mm 3.6 Ohm motor. With a 0.76mm shaft this motor is a good match for the 28mm tri-prop or 46mm SL wide blade. (more info) (NEW Lower Price for multi-pack)

	7mm KC9 Motor Width: 7mm 2.7 Ohm motor. With Length: 29mm Weight: 2.51 grams (more info)
	7mm x 16mm Negative Can Diameter: 7mm Length: 16mm Voltge: 1S (3.7V) Direction: Negative (Anticlockwise) (more info)
	7mm x 16mm Positive Can Diameter: 7mm Length: 16mm Voltge: 1S (3.7V) Direction: Positive (Clockwise) (more info)
	7mm x 20mm Negative Can Diameter: 7mm Length: 20mm Voltge: 1S (3.7V) Direction: Negative (Anticlockwise) (more info)
	7mm x 20mm Positive Can Diameter: 7mm Length: 20mm Voltge: 1S (3.7V) Direction: Positive (Clockwise) (more info)

7mm x 16.5mm 3.3 Ohm
These are great little motors, and a direct replacement for the SS Orange (they are the same motor) and has a micro connector pre-installed. These motors have long 60mm leads for easy installation and a 1mm Shaft. weight is 2.9g
(more info)
(NEW Lower Price for multi-pack)

	7mm 45000RPM Drive Motor: 7mm 45000 RPM Prop: 75mm Weight: 4.4 grams (more info)
	8.5mm x 20mm Positive Can Diameter: 8.5mm Length: 20mm Voltge: 1S (3.7V) Direction: Positive (Clockwise) (more info)
	8.5mm x 20mm Negative Can Diameter: 8.5mm Length: 20mm Voltge: 1S (3.7V) Direction: Negative (Anticlockwise) (more info)
	Brushed 8.6x20mm 2.4 Ohm Lower revs than other 8 mm motors and a 1.0mm shaft allow a good range of prop savers and adapters. (more info) (NEW Lower Price for multi-pack)
	Motor Mount for 8mm Motors Size: 17.2mm x 5.9mm Weight: 0.72grams (more info)
	10mm Positive Motor Can Diameter: 10mm Length: 21mm Voltge: 1S (3.7V) Direction: Positive (Clockwise) (more info)
	10mm Negative Motor Can Diameter: 10mm Length: 21mm Voltge: 1S (3.7V) Direction: Negative (Anticlockwise) (more info)
	N30 Motor with CR Prop Size: 25mm x 14mm Prop Size: 75mm CR Weight: 5.5grams Thrust: 42 - 48 grams (more info) (NEW Lower Price for multi-pack)
	N30 Motor with FR Prop Size: 25mm x 14mm Prop Size: 75mm FR Weight: 5.5grams Thrust: 42 - 48 grams (more info) (NEW Lower Price for multi-pack)

Brushless Motors (Rx -> ESC -> Motor)

	Motor D1103 8200kv Voltage: 1S (3.7volts) KV Rating: 8500kv Shaft: 1.5mm (more info)
	MT1410 3500kv Motor Voltage: 1-2S KV Rating: 3500kv Prop Adapter: 4mm (more info)
	MT1410 4000kv Motor Voltage: 1-2S KV Rating: 4000kv Prop Adapter: 4mm (more info)
	Motor D0703 20000KV Voltage: 1S (3.7 volts) KV Rating: 20,000kv Prop Shaft: 1.0mm (more info)
	7700kv Brushless This is a very powerful direct drive motor for it's weight. Coupled with a 3.7v battery and ESC this motor can offer greater thrust than a brushed motor / gearbox combo of similar weight. (more info)

AP-02 Brushless
This is a high quality motor. It is precision wound with silver-copper wire and ultra hard-press laminations. It will give extreme performance and efficiency being designed to run with a single LiPo cell and micro ESC.
(more info)

AP-03 Brushless
This powerful motor will give up to 44 grams of thrust for just 3.1 grams of weight. With such a good thrust to weight ratio it is perfect for micro 3D planes.
(more info)

	AP-05 Brushless A 5000kv motor for 1S applications delivering 90 grams of thrust with a GWS 5030 prop. (more info)
	AP0X Motor Mounts 1mm Plywood Height: 18mm Width: 22mm (more info)
	1813-3800KV Brushless This 3800kv motor is best suited to 2S (7.4 volt) applications. Prop and thrust data available. (more info)

Motor Mounts and Accessories

Motor Mount for 4mm Motors
Carbon rod mount for 4mm motors. Press in for firm fit and mounting hole for 0.8mm carbon rod.
(more info)

Motor Mount for 6mm Motors
Carbon rod mount for 6mm motors. Press in for firm fit and mounting hole for 0.8mm carbon rod.
(more info)

	Motor Mount for 6mm Motors Carbon rod mount for 6mm motors. Press in for firm fit and mounting hole for 1.0mm carbon rod. (more info)
	Motor Mount for 6mm Motors Carbon rod mount for 6mm motors. Mounting holes for both 1.0mm round and 1.5mm square carbon rods. (more info)
	Motor Mount for 7mm Motors Carbon rod mount for 7mm motors. Press in for firm fit and mounting hole for 0.8mm carbon rod. (more info)

Hard Motor Mount Spacers
Spacers for adjusting thrust angle. .
(more info)


Motor Sets
	Motor Set 6mm x 15mm Can Diameter: 6mm Length: 15mm Voltge: 1S (3.7V) (more info)
	Motor Set 7mm x 16mm Can Diameter: 7mm Length: 16mm Voltge: 1S (3.7V) (more info)
	Motor Set x 7mm x 20mm These motors are tuned to run in opposite directions. Perfect for dual prop planes or pusher props. (more info)
	Motor Set x 8.5mm x 20mm These motors are tuned to run in opposite directions. Perfect for dual prop planes or pusher props. (more info)
	Motor Set 10mm x 21mm Can Diameter: 10mm Length: 21mm Voltge: 1S (3.7V) (more info)