MicronWings Mini Delta White Airframe Kit

Price: 

29.50 AUD

18 in stock

Category

Specifications:

Wingspan 46cm
Airframe 31 grams
Flying
Weight
49-85 grams
Channels 3

Build Instructions

Overview
The new Mini Delta V2 is designed for stable long duration flights. While not being suitable for aerobatics, this airframe excels in its stability and straight tracking. Designed with micro FPV setups in mind, this airframe features two component bays (top and bottom) which give ample room for large batteries, multiple batteries and FPV gear.

With a wingspan of just 46cm (18 inches), the Mini Delta is suitable for outdoor flight in calm conditions with no wind or indoor stadium flight.

Note: This airframe is supplied without any electronics or motor.
Please see below for suggested electronics packages.

Colour Selection
This airframe is available in all white or white with grey trimmings.


Airframe Overview

Flight Videos
Flight Video – Morning flight with slow motion

Flight Video – Late afternoon flying with no wind and a few landings at the end.
This plane is fitted out with a 950mah battery and an all up flying weight of 63 grams.

Flight Video – Late afternoon with a little breeze.
This plane is fitted out with a 950mah battery and an all up flying weight of 63 grams.

Flight Video – Landings with slow motion

Electronics Bays
The top canopy houses the main electronics bay with ample space for large batteries, receiver, ESC and an optional FPV camera mount at the front.

The bottom electronics bay is suitable for housing a directly soldered ESC or an FPV transmitter.

FPV Options
The Mini Delta has been designed from the ground up to accommodate micro FPV units as shown here.
The bottom electronics bay is perfectly suited for housing the FPV transmitter and the kit is supplied with both a standard canopy skin and a skin with a cut-out for an FPV camera.

FPV Flight Video

Construction Materials
The Mini Delta is supplied in kit form and needs to be constructed. It features a balsa and Paulownia wood frame with carbon rod supports. Genuine Depron is used for all other airframe coverings. 3mm Depron for the canopy hatches and wing tip fins, 6mm Depron for the airframe sides and 2mm Depron for the wing skins.

Airframe Construction VideoS

The build videos below show the step by step construction of this airframe. There are also links in the assembly instructions to the relevant section of these videos.
Build Video – Part 01 Build Video – Part 02

 

Suggested Electronics Packages
The wing ribs are specifically designed to accommodate 5320 or 5330 type servos. We suggest the following electronics packages.
Receivers
Micro sub 2.5 gram receivers with built in brushless ESC. These are the latest style receiver with a built in 5amp brushless ESC available for both DSMX/2 and FRSky
DSMX/2

FRSky
The Micro receivers below without an onboard brushless ESC can be used in combination with a separate 3 Amp brushless ESC unit.
DSMX/2

FRSky

Servos
This airframe is designed to accommodate either 5320 or 5330 servos. Servos with SH connectors fit the receivers shown above.
5320 Black SH

5320 White SH

5330 Black SH

5330 White SH

ESC Units
3 Amp ESC units which are suitable for the receivers above and for the suggested motor / prop combinations below.
ESC Micro 3A
ESC Micro MX 3A
ESC XP 3A
Recommended Brushless Motors
Motors suitable for 1S Operation
AP03 7000kv

D1103 8,200KV

Propellers
Propeller and Prop Saver combinations. We recommend using a prop saver and prop with a 4mm bore instead of a propeller with a 1.5mm bore which fixes directly to the motor shaft. Using a prop saver prevents the motor shaft from damage when belly landing this plane.
90mm eProp
Prop Saver 1.5mm
O-rings

Batteries
This airframe can accommodate a range of battery sizes from 300mah to 950mah. However, we recommend at least a 500mah battery for best balance. If using a lighter 300mah battery, you will also need to add some ballast to the front of the airframe to achieve the correct balance point.
Nanotech 950mah

Nanotech 300mah

Nanotech 750mah

 
Extra Ballast Required

Transmitter Setup
As this model uses elevons, you will be required to setup your transmitter for elevon mixing.
Ensure that you are able to do this before purchasing.